Every second enquiry from a German buyer asks the same question in a different way: what paperwork do I need? The honest answer is that the CE declaration is the easy part, and it is the part everyone has. The documents that stop containers are the ones nobody puts on a quotation: the WEEE registration number, the packaging system contract, and the timber origin file.
This is the order we work through with importers. It is written from the supplier side — what we can hand you and what only you can do.
1. The technical file behind the CE mark
A cold plunge is an electrical appliance with a compressor, a pump and a control board. In the EU that means, at minimum:
- Low Voltage Directive 2014/35/EU — safety of the electrical equipment, tested against the EN 60335 series for household and similar appliances
- EMC Directive 2014/30/EU — emissions and immunity, typically the EN 55014 and EN 61000 series
- RoHS 2011/65/EU — restricted substances, with a material declaration from the board and harness suppliers
- An EU Declaration of Conformity naming the standards applied and signed by the manufacturer
The failure mode here is not a missing certificate. It is a certificate that covers one model while the container holds four. Customs rarely checks this; a marketplace compliance team or a competitor’s lawyer will. Ask for the model list attached to the test report and compare it against your purchase order line by line.
For the chiller range we quote, the units are documented under an Intertek-issued authorization to mark, with the accompanying test report covering the model range (report 240400096SHA-001, control no. 5029677, covering QG-10-RB, QG-0.5HP-110V, QG-RA-12 and QG-RA-15). If you need the report number written into your technical file, ask for it with the RFQ and we will send the copy.
2. An EU responsible person (GPSR)
Since 13 December 2024, Regulation (EU) 2023/988 on general product safety requires every consumer product on the EU market to have an economic operator established in the EU who can be held responsible for it. For a manufacturer outside the EU, that person’s name, postal address and electronic contact have to be on the product or its packaging.
In practice this is your German distributor, your fulfilment partner, or an authorised-representative service. It is a commercial arrangement, not a form we can fill in for you — but we will print whatever block you specify on the nameplate and the carton, and we will hold the artwork version you approved.
3. WEEE registration (ElektroG)
A cold plunge contains a compressor, a pump and electronics. In Germany that makes it an electrical appliance under the Elektrogesetz, and the first party placing it on the market has to be registered with stiftung ear before it is offered for sale. Retailers and marketplaces check the WEEE-Reg.-Nr. as a matter of routine, and Amazon will block a listing without it.
Registration is not instant. Start it before the container is booked, not after it clears customs.
4. Packaging EPR (VerpackG / LUCID)
Every carton, pallet wrap, foam insert and wooden crate you import is packaging you have placed on the market. That means a LUCID registration, a contract with a dual system, and quantity declarations. Non-registration carries a distribution ban, and it is enforced against the importer, not the exporter.
We can give you the packaging weights and material breakdown per unit — carton, foam, film, pallet, crate — so the declaration is based on real numbers rather than an estimate.
5. Timber due diligence (EUTR now, EUDR next)
Barrel saunas, timber tubs and cladding are wood products. Today the applicable regime is the EU Timber Regulation 995/2010: the importer operates a due diligence system and needs, for each shipment, the species, the country and region of harvest, the concession or supply area, and a supplier declaration.
The EUDR (Regulation (EU) 2023/1115) replaces it and adds geolocation of the plot. Its application date has already moved twice following the targeted revision, and the current schedule puts large and medium operators at the end of 2026 with a further window for micro and small operators. Treat the date as something to confirm with your importer or the BLE guidance rather than something read off a blog — including this one.
What does not change with the date: the geolocation data takes months to assemble and cannot be produced retroactively for timber already cut. If you are planning a German launch next year, ask your supplier for species, harvest region and sawmill now.
6. Refrigerant, treatments and finishes
- Refrigerant charge — the F-gas Regulation (EU) 2024/573 applies. The charge weight goes on the nameplate. A sealed unit charged with a few hundred grams of R32 sits far below the leak-check threshold (5 t CO₂e, roughly 7 kg of R32 at GWP 675), but the number still has to be declared and it still has to match what is actually in the circuit.
- Timber treatment — if the wood is chemically preserved rather than heat-treated, the Biocidal Products Regulation comes into play. Thermally modified spruce avoids the question entirely, which is one reason it is popular in Europe.
- Coatings and adhesives — a REACH SVHC declaration and a VOC statement for anything with a finish on it.
7. Customs classification
Agree the HS code with your broker before you book. The chiller and the tub are frequently declared under different headings, and the code changes both the duty rate and the import VAT base. The headings that usually apply are 8418 69 for refrigerating equipment, 9406 80 for prefabricated wooden structures, and 8516 29 for the sauna heater — confirm each one for your specific configuration.
The checklist
| Document | Who produces it | When it is needed | Common failure |
|---|---|---|---|
| EU Declaration of Conformity | Manufacturer | Before first sale | Model list does not match the shipped models |
| LVD / EMC / RoHS test reports | Accredited lab | Technical file, on request | Report predates a component change |
| EU responsible person details | Importer | Before labelling | Added to the carton, not the product |
| WEEE-Reg.-Nr. | Importer (stiftung ear) | Before listing | Started after the shipment arrives |
| LUCID + dual system contract | Importer | Before import | Missing for the wooden crate |
| Timber species, origin, supplier declaration | Manufacturer | Every shipment | Country only, no region or concession |
| EUDR geolocation set | Manufacturer + sawmill | Ahead of EUDR application | Left until the last minute |
| Refrigerant charge declaration | Manufacturer | Nameplate + technical file | Nameplate differs from the actual charge |
| REACH SVHC / VOC statement | Manufacturer | On request | Only covers the timber, not the coating |
| HS code confirmation | Customs broker | Before booking | Chiller and tub declared as one item |
What we hand over with the goods
- Declaration of Conformity, signed, with the standards listed
- Test reports covering the shipped model range
- Nameplate artwork including the EU responsible-person block you specify
- Packaging weights and materials per unit for your LUCID declaration
- Timber species, harvest region and sawmill reference for the due diligence file
- Refrigerant type and charge weight per unit
- Spare parts list, exploded drawings, and a two-year spare availability commitment
None of this is legal advice, and none of it substitutes for your own importer obligations — the registration numbers are yours to hold. But the supplier half of the file should arrive complete and in one folder, not in eleven emails over three weeks. If you are building a German or wider EU launch, start the RFQ with the market and the volume and we will send the document set alongside the quote.
For the manufacturing and testing side of the same story, see quality and testing.