A buyer in Texas asks for the same tub as a buyer in Munich and adds one line to the email: “just send it with a US plug.” That single sentence is where a surprising number of cold plunge projects start to go wrong, because the plug is the only part of the electrical specification that can actually be changed on the dock.
Three things vary between markets, and they are not equally easy to solve: the voltage, the frequency, and the conformity mark. The first is nearly free. The second is a hardware decision. The third is a documentation project that starts long before the order.
Frequency matters more than voltage
An induction motor’s synchronous speed is proportional to the supply frequency. Put a 60 Hz motor on a 50 Hz supply and it runs at about 83 % of its design speed. The pump moves less water, the condenser fan moves less air, and the compressor’s internal cooling drops — while the load it is trying to carry has not changed. The unit still runs. It just runs hotter, and it fails earlier, usually in the second summer.
Run a 50 Hz motor on 60 Hz and the opposite happens: 20 % overspeed, higher flow than the circuit was designed for, more noise, and a compressor working outside its intended envelope.
Voltage is more forgiving. Most control boards today run on switch-mode supplies with a wide input range, and a 230 V-rated board is usually happy at 220 V or 240 V. The compressor, the pump and the fan are the parts that care, and they care about frequency first.
| Market | Supply | Typical plug | Conformity mark to expect |
|---|---|---|---|
| United States | 120 V / 60 Hz, single phase | NEMA 5-15 | UL or ETL listing |
| Canada | 120 V / 60 Hz | NEMA 5-15 | cUL or cETL |
| European Union | 230 V / 50 Hz | CEE 7/3 (Schuko) | CE |
| United Kingdom | 230 V / 50 Hz | BS 1363 | UKCA, with CE still accepted for most goods under the current extension |
| Australia / NZ | 230 V / 50 Hz | AS/NZS 3112 | RCM |
| Japan | 100 V, 50 Hz east / 60 Hz west | NEMA 5-15 | PSE |
Japan is the case that catches people out: one country, two frequencies, split roughly along the Fuji line. A unit destined for Tokyo and a unit destined for Osaka are not the same unit.
One CE certificate does not cover the world
CE is a self-declaration against EU directives — low voltage, EMC, RoHS — supported by test reports from an accredited laboratory. It is not recognised in the United States, where the retailer will ask for a UL or ETL listing from a Nationally Recognized Testing Laboratory. It is not recognised in the UK, which has its own mark. It is not recognised in Australia, which wants RCM.
The CB Scheme is often presented as a shortcut. It is not a mark; it is an agreement that allows test reports to be recognised between member certification bodies. It saves testing time when you are certifying for a second market, but you still need the national mark at the end of it.
The practical consequence for a supplier is that the same physical chiller may exist in three documentation variants. When you ask for a quotation, ask which variants exist for the model you are being offered, and ask for the model list attached to each report. A test report covering one model in a four-model shipment is the most common gap we see in technical files.
The chiller is the hard part
Three details decide whether the installation actually works:
- Starting current. A compressor draws several times its running current for a fraction of a second at start-up. The breaker and cable have to be sized for that, not for the nameplate running watts. This is where a unit that “works on the bench” trips a household circuit in a garage.
- Fixed speed or inverter. An inverter-driven compressor can be built to run on either frequency, which simplifies a multi-market product. A fixed-speed compressor cannot. That difference is visible on the quotation as a model number, not always as a line item.
- Refrigerant and charge. R32 is the common choice now, and the charge weight belongs on the nameplate. In the EU the F-gas rules apply to the charge, not to the marketing description — the number on the plate has to match what is in the circuit.
The sauna heater is easier, but not trivial
A resistive heater is a simpler thing than a compressor: no motor, no frequency dependence, and the same element works on 50 Hz or 60 Hz. What changes is the supply it is wired to. A 9 kW heater on a 230 V single-phase supply draws around 39 A, which is a dedicated circuit, a specific cable size, and a conversation with an electrician before the cabin is positioned — not after.
Three-phase supply is common in Nordic and German installations and rare in UK domestic ones. If a project assumes three-phase and the building does not have it, the fix is a new supply, and the cost sits with the site rather than the product.
Four things to send with an enquiry
- Destination country, not just the continent. The UK is not the EU for marking purposes, and Japan is two countries electrically.
- Voltage, frequency and phase available at the installation point — and the breaker rating, if the client already knows it.
- Where the unit will sit: indoor plant room or outdoor, and the summer ambient it will see. A chiller in a closed cupboard is a warranty claim waiting to happen.
- Which mark the channel requires. A marketplace, a electrical wholesaler and a hotel’s M&E consultant will each ask for something different, and it is cheaper to know before the model is fixed.
None of this is exotic. It is simply the difference between quoting a product and quoting a product that will pass inspection in the country it is going to. Send the destination, the supply and the format and we will come back with the model that matches, or tell you honestly that the model you have in mind is the wrong one for that market.
For the documentation side of the same question, the German import checklist sets out the file in the order an importer needs it.